Argo AE3MI70AH Manual de instalación

85264189902000ContentsPageIMPORTANT!Please Read Before Starting ... 11. GENERAL...

82-2. Embedding the Tubing and Wiring● Before beginning embedding installation work, con-sult fully with agencies or offices related to the build-ing

9Set screw only for transportationFig. 5aScrewAttachment tabRear panelFig. 5bRear panel▲ marksFig. 6aLeft tubingRight tubingDownward tubingRight-rear

10IndoorsideOutdoorsidePlasticcoverINSIDE OUTSIDEWallSlightanglePVC pipePlastic coverFig. 10PVC pipe (locally purchased)Cut at slight angleFig. 9(4) U

11(2) Double check with a ruler or carpenter’s level thatthe panel is level. This is important to install the unitproperly. (Fig. 12)(3) Make sure the

12How to replace the grille(1) Close the flaps.(2) Reinstall the grille into the lower part while aligningits tabs on the upper part. (Fig. 15a) Inser

133-7. Wiring Instructions for Inter-unit Connections(1) Hold both corners of the air intake grille, then pullout and up to open.(2) Remove the screw

14When connecting each power wire to the correspond-ing terminal, follow the instructions “How to connectwiring to the terminal” and fasten the wire s

153-8. Mounting(1) To install the indoor unit, mount the indoor unit ontothe tabs on the upper part of the rear plate.(2) Hold down the air discharge

16Hole in wallBent partNarrow tubeWide tubeRear panelFig. 27aDrain capDrain hoseFig. 27b Left-side tubing(1) Lead the tubing and drain hose through t

17To unmount indoor unitPress the 2 ▲▲ marks on the lower part of the indoorunit and unlatch the tabs. Then lift the indoor unit andunmount. (Fig. 29)

184. How to Secure the Wireless RemoteControl UnitThe remote control unit can be operated from either anon-fixed position or a wall-mounted position

Fig. 34aFig. 34bFig. 35Fig. 36Indoor unitR.OUT connectoron circuit boardIndoor unit extended-connection cord (8 m): Available separatelySTK-WS0508WRem

206. Test Run(1) Turn the indoor unit selector switch to the “ON” position. (Fig. 37)(2) With the remote controller, start heating or coolingoperatio

Via Varese, 90 - 21013 Gallarate - Va - ItalyTel. +39 0331 755111 - Fax +39 0331 776240www.argoclima.itCOP-INVERTER-ARGO.qxd 6-02-2004 16:07 Pagina

1IMPORTANT! Please Read Before StartingThis air conditioning system meets strict safety and oper-ating standards. As the installer or service person,

21. GeneralThis booklet briefly outlines where and how to installthe air conditioning system. Please read over the entireset of instructions for the

31-5. Additional Materials Required for Installation1. Refrigeration (armored) tape2. Insulated staples or clamps for connecting wire(See local codes

4● install in a sturdy manner to avoid increased operat-ing noise.● install the unit within the maximum elevation differ-ence (H1, H2, H3, H4) above o

Fig. 2a5(1) Connecting indoor unit types (28 – 36) at Bφ6.35φ6.35φ9.52φ9.52AB(28 36 type)Outdoor unitIndoor unit(28 36 type)(2) Connecting indoor un

6Fig. 2eFig. 2fφ6.35φ6.35φ6.35φ9.52φ9.52Union φ12.7φ9.52φ9.52φ9.52ABC(28 36 types)Outdoor unitIndoor unit(28 36 types)(50 type)Flare φ9.52 Union φ12

7AE4MI91AHφ6.35φ6.35φ6.35φ6.35φ9.52φ9.52φ9.52φ9.52φ9.52Aφ9.52Bφ9.52COutdoor unitIndoor unitUnion φ9.52Flare φ12.7φ12.7D(φ12.7 → φ9.52) Supplied Reduc